DieselShip's Online Content Library

Q4: A. With reference to MARPOL 73/78, elaborate upon the Second Engineer’s responsibilities with regard to – (10)

i) Avoidance of pollution near coastal and port areas.

 ii) Avoidance of pollution of port atmosphere with smoke.

B. With reference to SOLAS 74 as amended, discuss the following: (10)

i) How fire alarms are distinguished from other alarms.

ii) The requirements for an emergency power supply

Q3. A. With reference to the underwater surface of a ship’s hull; i. Describe a hull plate roughness analyser system;

ii. State the significance of the roughness profile and compare the typical roughness values for a new ship and a ship eight years old;

B. Which reference to the application of self-polishing paint in dry dock - i. Describe the plate preparation necessary;

ii. State the defects that may occur in the paint coating if it is not correctly applied.

Q1. With reference to International Load Line Statutory Certification,

A. State the reasons for the freeboard requirements;

B. (i) Explain the term “conditions of assignments”;

(ii) List the items that may be examined during a Load line survey after a vessel’s major repairs in the dry-dock.

Q1. Describe the relationship between frictional resistance and

(a) Ship’s speed;

(b) the wetted area;

(c) surface roughness;

(d) The length of the vessel.

Q5. Describe - A. A safety lamp approved as part of slips statutory equipment LIFEBUOY SELF –IGNITING LIGHTS; B. A self-igniting lamp suitable for attachment to a lifebuoy; C. State the attention required to maintain them in a satisfactory working condition.

Q5. With reference to air receivers and bottles explain with reasons: A. Why regular systematic internal inspection is advisable? B. Which internal areas of large receivers should receive particularly close examination? C. How bottles are inspected internally and what parts should be closely examined? D. How the condition of a bottle or receiver that cannot be inspected internally is checked?

Q6. A. Describe the events leading to a crankcase explosion.

B. State how overheating might be indicated other than by a mist detector.

C. Discuss the procedure to follow in the invent of overheating being indicated.

D. State how severity of a crankcase explosion is limited.

Q1: Describe how the following conditions are prevented in auxiliary boilers:

A. Feed contamination by oil from heating coil drains.

B. Internal corrosion.

C. Furnace blowback.

D. Uptake fire.

Q1: A. Outline the procedure for the inspection of the rudder in a dry dock.

B. What are the requirement with respect to steeling gear as per SOLAS 74, as amended for the following:

i. Relief valve;

ii. Steering gear control;

iii. Electrical power circuits.

Q8. With respect to hydraulic Ram steering gears;

A. What emergency locking device can be used in order to speedily bring the steering gear to rest? State one reason the best angular position to lock the steering gear.

B. Use a simple sketch to show where the “Jumping” (top) and wear down (bottom) rudder carrier ring clearances can be measured. Indicate what clearances you would expect with a new steering gear;

C. State the consequences of the wear down clearances being reduced to less than Zero.

Q1. A. Sketch a circuit diagram of a push button direct online contactor starter for a three phase Incorporating overload and short circuit protection.

B. Indicate, on a sketch of the typical characteristic curves of current and torque against Speed, disadvantages of a direct on line start squirrel cage induction motor.

Q9. A. Discuss different methods of speed control of a d.c. series motor by adjusting field ampere turns.

B. A 230 V, d.c. shunt motor runs at 1000 r.p.m and takes 5 amperes. The armature resistance of the motor is 0.025𝛀 and shunt field resistance is 230𝛀. Calculate the drop in speed when the motor is loaded and takes the line current of 41 amperes. Neglect armature reaction.

Q2. Sketch a high-lift safety-valve lid and seat detailing their special features. Describe how such a valve is overhauled and any clearance that should be measured and noted. (16)

Q2. With reference to the carriage and pumping of liquefied gas cargo:

A. Sketch a suitable pumping system labelling the component parts;

B. State;

i) Why submerged hydraulically driven pumps are not used;

ii) How overheating of pump drive shaft bearings is avoided;

C. State, how the risk of fire and explosion in cargo tanks is obviated both in the loaded and discharged condition.

Q6. With regards to main transmission shaft flange coupling arrangements:

A. Sketch a hollow type coupling bolt and the hydraulic head/nut and loading rod which are used to fit it.

B. Describe how the bolt is fitted.

C. State the advantage of the hollow coupling bolt as compared to the traditional type of coupling bolt.