DieselShip's Online Content Library

Q6. A ship 90 m long displaces 5200 tonne and floats at draughts of 4.95m forward and 5.35 m aft when in sea water of 1023 kg/m3. The water plane area is 1100m2, GML 95m, LCB 0.6m forward of midships and LCF 2.2m aft of midships. Calculate the new draughts when the vessel moves into fresh water of 1002 kg/m3

Q9. With respect to Buoyancy of a vessel:

A. What do you understand by reserve buoyancy what happen if the lost buoyancy is greater than the reserve buoyancy?

B. A forward deep tank 12 m long extends from a longitudinal bulkhead to the ship’s side. The widths of the tank surface measured from the longitudinal bulkhead at regular intervals are 10, 9, 7, 4 and 1 m. Calculate the second moment of area of the tank surface about a longitudinal axis passing through its centroid.

Q9. With respect to Inclining Experiments onboard vessels;

A. Sketch and Describe briefly the inclining experiment and explain how the results are used.

B. A forward deep tank 12 m long extends from a longitudinal bulkhead to the ship’s side. The widths of the tank surface measured from the longitudinal bulkhead at regular intervals are 10, 9, 7, 4 and 1 m. Calculate the second moment of area of the tank surface about a longitudinal axis passing through its centroid.

Q4. Give a pragmatic approach to dealing with a sea water leakage, which is flooding the engine room and which has the potential of causing a serious impairment to a vessels stability.

Q6. With reference to an automatic water sprinkler, fire detecting alarm and extinguishing system for accommodation spaces: -

A. (i) Sketch a typical system;

(ii) Describe the operation of this system;

B. State the sources of water available;

C. Describe the sprinkler head and its operation;

D. State how the temperature rating of the sprinkler head is determined.

Q6. A. State the circumstances owing to which it may be necessary to renew a cylinder liner.

B. Explain how the liner is removed

C. Explain how the new liner is fitted; State the important checks to be made before and after fitting.

Q6. Under Continuous survey of machinery (CSM) bottom end bearing of a large 2stroke slow speed engine is due for survey.

A. As second engineer, explain the procedure involved in complete inspection of a bottom end bearing.

B. List the precaution to be taken.

C. Indicate the reasons for possible defects which could be encountered and state how they may be rectified.

D. What test are carried out on completion of survey and re-assembly.

Q4. Accidents regularly occur due to premature or accidental release of CO2 into machinery spaces. With reference to this, enumerate the procedure or arrangement that you as second engineer would adopt with respect of the following

A.  Contractors working on CO2 system;

B. Understanding between bridge and engine room in the event of a machinery space fire;

C. Familiarizing staff with the system;

D. Checks and tests are carried out before putting system in operation?

Q3. A. Sketch and describe TWO methods that employ manometric means for measuring tank contents. (6)

B. State what corrections are made to the readings obtained by the methods described in (A) in order to gauge the mass contents? (5)

C. Explain how bunkering requirements may be estimated when no records of main engine fuel consumption are available on board. (5)

Q2. Sketch a high-lift safety-valve lid and seat detailing their special features. Describe how such a valve is overhauled and any clearance that should be measured and noted. (16)

Q9. With reference to fatigue of engineering components:

A. Explain the influence of stress level at cyclical frequency on expected operating life.

B. Explain the influence of material defects on the safe operating life of engineering component.

C. State the factors which influence the possibility of fatigue cracking of an auxiliary boiler feed water pump shaft and explain how the risk of such cracking can be minimized.

Q1. With reference to a particular make of main propulsion unit, describe how the engine is reversed manually and discuss the problems involved and the safety precautions which would be required if the control were operated remote from the machinery space.