0 votes
1k views
How  is  the  oil  quill  fitted  in  the  B&W engine. Explain  by  a  sketch
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
866 views
What  is  the  expansion  arrangement  in  the  main  engine  exhaust   valve.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
884 views
How  is  the  lead  in  the  sulzer  fuel  pump  checked. How is  the  cam  fitted,  is  it  a  s...
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
768 views
In  the  domestic  refrigerator  how  is  hot  gas  defrosting  done.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
1k views
Explain  the  telescopic  pipe  seal  arrangements.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
834 views
What  are  the  ways  to  improve  the  thermal  efficiency  of  the  engine.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
0 answers
831 views
Explain  the  procedure  of  finding  the  indicated  power  of  the  engine.
0 votes
0 answers
957 views
Describe  the  procedure  for  taking  thrust block  pad clearance
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
1k views
Describe  the  procedure  for  overhauling  the  main  engine  exhaust  valve and  what clearance...
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
913 views
Describe  the  procedure  for  removal  of  the  main  engine  fuel pump  and  barrel.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
918 views
Describe  the  procedure  for  cutting  off  a unit  of  the  engine. How  will  you  set  the  e...
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
822 views
How  is  the  indicated  power  found  and  how  it  is  calculated.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
2k views
How  is  the  SFOC  calculated  and  in  what  units  is  it  expressed
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
0 answers
781 views
Describe  the  procedure  for  dismantling  the  main  engine   bottom  end  bearing.
0 votes
795 views
Sketch the  T/C and  show  the  various  components  in  it  and  their purpose.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
772 views
Explain the  principle  of  pneumatic   controllers  used  in  automation.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
716 views
What  is  the  reason  for  the  hardness  of  the  boiler  water.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
723 views
Main S/W line cracked during sailing. As a second engineer how will you fabricate new pipe line ?
  • Kalai asked 2 years ago
  • last active 1 year ago
0 votes
798 views
In the hydraulic type governor why is the governor RPM more than the engine RPM ?
  • Kalai asked 2 years ago
  • last active 1 year ago
0 votes
1k views
0 votes
877 views
Describe the procedure for A/E fuel pump timing verification and setting.
  • Kalai asked 2 years ago
  • last active 1 year ago
0 votes
650 views
In the IG system state the setting values for the PV valves and the PV breaker. What percentage o...
  • Kalai asked 2 years ago
  • last active 1 year ago
0 votes
427 views
0 votes
698 views
How would you carry out crank case inspection of the main engine and what clearances ...
Showing 51 - 100 of 134 results