0 votes
0 answers
229 views
I gave my oral on 16th APRIL still results not updated in my profile..Pls advise do I need to co...
0 votes
300 views
Can we book for june, the subjects failed in april??
0 votes
225 views
Why we need imsbc code when we had BC code. Anyone please throw some light on above
0 votes
242 views
Is it allowed to book oral in successive months ? It seems possible online, will examiners object?
0 votes
348 views
On what basis a flag state can reject or suspend RO status of Class. Where it is stated Is it ...
0 votes
322 views
Why in STOPIA 29548 gt or less tankers…? What is the significance of that number…?
0 votes
307 views
who will pay if the claims due to oil pollution on tankers are more than supplementary fund limit...
0 votes
343 views
What will happen if Bill Of lading doesn’t reach consignee by the time of cargo discharge&#...
0 votes
0 answers
258 views
dear sir, weight and pressure of pilot bottles.? how we came to know that after 2 minutes of ope...
0 votes
0 answers
715 views
How to check main engine fuel pump zero setting?
0 votes
610 views
Boiler furnace checks
0 votes
686 views
What are reasons  for  surging  of  the  main  engine  T/C
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
555 views
If   the  main  engine  is  not  performing  well  how  will  you  find  out  ,  investigate  and...
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
736 views
Explain  the  reasons  for  seals  in  the  fuel  pump of  main  engine  and  why  are  they  req...
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
586 views
How  is  the  humidity  of  the  air  controlled  in  an  air  conditioner.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
0 answers
573 views
How  are  the  thrust  pad  clearances  measured  on  the  ahead  and  astern  pads.
0 votes
711 views
How  is  the  oil  quill  fitted  in  the  B&W engine. Explain  by  a  sketch
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
583 views
What  is  the  expansion  arrangement  in  the  main  engine  exhaust   valve.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
600 views
How  is  the  lead  in  the  sulzer  fuel  pump  checked. How is  the  cam  fitted,  is  it  a  s...
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
516 views
In  the  domestic  refrigerator  how  is  hot  gas  defrosting  done.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
712 views
Explain  the  telescopic  pipe  seal  arrangements.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
580 views
What  are  the  ways  to  improve  the  thermal  efficiency  of  the  engine.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
0 answers
609 views
Explain  the  procedure  of  finding  the  indicated  power  of  the  engine.
0 votes
0 answers
694 views
Describe  the  procedure  for  taking  thrust block  pad clearance
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
746 views
Describe  the  procedure  for  overhauling  the  main  engine  exhaust  valve and  what clearance...
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
645 views
Describe  the  procedure  for  removal  of  the  main  engine  fuel pump  and  barrel.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
622 views
Describe  the  procedure  for  cutting  off  a unit  of  the  engine. How  will  you  set  the  e...
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
525 views
How  is  the  indicated  power  found  and  how  it  is  calculated.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
927 views
How  is  the  SFOC  calculated  and  in  what  units  is  it  expressed
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
0 answers
517 views
Describe  the  procedure  for  dismantling  the  main  engine   bottom  end  bearing.
0 votes
512 views
Sketch the  T/C and  show  the  various  components  in  it  and  their purpose.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
523 views
Explain the  principle  of  pneumatic   controllers  used  in  automation.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
485 views
What  is  the  reason  for  the  hardness  of  the  boiler  water.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
472 views
Main S/W line cracked during sailing. As a second engineer how will you fabricate new pipe line ?
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
533 views
In the hydraulic type governor why is the governor RPM more than the engine RPM ?
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
563 views
Describe the procedure for A/E fuel pump timing verification and setting.
  • Kalai asked 1 year ago
  • last active 1 year ago
0 votes
411 views
In the IG system state the setting values for the PV valves and the PV breaker. What percentage o...
  • Kalai asked 1 year ago
  • last active 1 year ago
Showing 1 - 50 of 99 results