Control Theory (19)
0 votes
0 answers
3k views
Can anyone tell me how the connection to telescopic pipe is arranged in MAN BW engine. I was aske...
- rajesh02991 asked 3 years ago
- aaakashjains asked 4 years ago
- last active 3 years ago
0 votes
0 answers
4k views
Adantagesof axial flow turbine overradial flow ?
- aaakashjains asked 4 years ago
0 votes
0 answers
6k views
How to check main engine fuel pump zero setting?
- istafakhan33 asked 6 years ago
What are reasons for surging of the main engine T/C
- Kalai asked 6 years ago
- last active 6 years ago
If the main engine is not performing well how will you find out , investigate and...
- Kalai asked 6 years ago
- last active 6 years ago
Explain the reasons for seals in the fuel pump of main engine and why are they req...
- Kalai asked 6 years ago
- last active 6 years ago
How is the humidity of the air controlled in an air conditioner.
- Kalai asked 6 years ago
- last active 6 years ago
0 votes
0 answers
5k views
How are the thrust pad clearances measured on the ahead and astern pads.
- Kalai asked 6 years ago
How is the oil quill fitted in the B&W engine. Explain by a sketch
- Kalai asked 6 years ago
- last active 6 years ago
What is the expansion arrangement in the main engine exhaust valve.
- Kalai asked 6 years ago
- last active 6 years ago
How is the lead in the sulzer fuel pump checked. How is the cam fitted, is it a s...
- Kalai asked 6 years ago
- last active 6 years ago
In the domestic refrigerator how is hot gas defrosting done.
- Kalai asked 6 years ago
- last active 6 years ago
Explain the telescopic pipe seal arrangements.
- Kalai asked 6 years ago
- last active 6 years ago
What are the ways to improve the thermal efficiency of the engine.
- Kalai asked 6 years ago
- last active 6 years ago
0 votes
0 answers
5k views
Explain the procedure of finding the indicated power of the engine.
- Kalai asked 6 years ago
0 votes
0 answers
6k views
Describe the procedure for taking thrust block pad clearance
- Kalai asked 6 years ago
- last active 6 years ago
Describe the procedure for overhauling the main engine exhaust valve and what clearance...
- Kalai asked 6 years ago
- last active 6 years ago
Describe the procedure for removal of the main engine fuel pump and barrel.
- Kalai asked 6 years ago
- last active 6 years ago
Describe the procedure for cutting off a unit of the engine. How will you set the e...
- Kalai asked 6 years ago
- last active 6 years ago
How is the indicated power found and how it is calculated.
- Kalai asked 6 years ago
- last active 6 years ago
How is the SFOC calculated and in what units is it expressed
- Kalai asked 6 years ago
- last active 6 years ago
0 votes
0 answers
5k views
Describe the procedure for dismantling the main engine bottom end bearing.
- Kalai asked 6 years ago
Sketch the T/C and show the various components in it and their purpose.
- Kalai asked 6 years ago
- last active 6 years ago
Explain the principle of pneumatic controllers used in automation.
- Kalai asked 6 years ago
- last active 6 years ago
What is the reason for the hardness of the boiler water.
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
Main S/W line cracked during sailing. As a second engineer how will you fabricate new pipe line ?
- Kalai asked 6 years ago
- last active 6 years ago
In the hydraulic type governor why is the governor RPM more than the engine RPM ?
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
Describe the procedure for A/E fuel pump timing verification and setting.
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
In the IG system state the setting values for the PV valves and the PV breaker. What percentage o...
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago
0 votes
0 answers
5k views
- Kalai asked 6 years ago
- last active 6 years ago
- Kalai asked 6 years ago
- last active 6 years ago