DieselShip

Ship Nomenclature

Load Line Length(m)- taken as 96 per cent of the total length on a waterline at 85 per cent of the least moulded depth measured from the top of the keel, or as the length from the fore side of the stern to the axis of the rudder stock on that waterline, if that is greater. In ships designed with a rake of keel, the waterline on which this length is measured is to be parallel to the designed waterline. The length is to be measured in metres.

LR Scantling Length-Rule length, is the distance, in metres, on the summer load waterline from the forward side of the stern to the after side of the rudder post or the centre of the rudder stock if there is no rudder post. L is to be not less than 96 per cent, and need not be greater than 97 per cent, of the extreme length on the summer load waterline.

The ship’s Draught D is the vertical distance from the waterline to that point of the hull which is deepest in the water The foremost draught D_F and aft most draught D_A are normally the same when the ship is in the loaded condition.

The Scantling Draught is the ships design draught and is equal to the Summer Load Line draught.

Breadth on waterline BWL-the largest breadth on the waterline B_WL

Displacement

This is the equivalent mass of sea water (sg = 1.025) displaced by the hull. It is therefore equal to the Total weight of the vessel

Deadweight

Deadweight is the difference in tonnes (1000Kg) between the displacement of a ship in water of specific gravity 1.025 at the load waterline corresponding to the assigned summer freeboard and the lightweight of the ship.
It includes bunkers and other supplies necessary for the vessel to proceed on passage as well as cargo.
The Deadweight may be quoted at the design draught although this would be specially denoted

Lightweight

Lightweight is the displacement of a ship in tonnes without cargo, fuel, lubricating oil, ballast water, fresh water and feedwater in tanks, consumable stores, and passengers and crew and their effects.

Thus
DISPLACEMENT = DEADWEIGHT + LIGHTWEIGHT

Gross Register Tonnage, Net Register Tons

This is a volume measurement where one Register Ton is equivalent to 2.83 m³ and express the total moulded internal size of the vessel and are used for the calculation of harbour and canal dues. It can be found on the International Tonnage Certificate each vessel must hold

Hull Form description

Parallel midbody In many modern ships, the form of the hull’s transverse section in the midships region extends without change for some distance fore and aft. This is called parallel midbody and may be described as extensive or short, or expressed as a fraction of the ship’s length.

Forebody The portion of the hull forward of the midship section.

After body The portion of the hull abaft the midship section.

Entrance The immersed portion of the hull forward of the section of greatest immersed area (not necessarily amidships) or forward of the parallel midbody.

Run The immersed portion of the hull aft of the section of greatest immersed area or aft of the parallel midbody.

Deadrise The departure of the bottom from a transverse horizontal line measured from the baseline at the molded breadth line. Deadrise is also called rise of floor or rise of bottom. Deadrise is an indicator of the ship’s form; fullbodied ships, such as cargo ships and tankers, have little or no deadrise, while fine-lined ships have much greater deadrise along with a large bilge radius. Where there is rise of floor, the line of the bottom commonly intersects the baseline some distance from the centerline, producing a small horizontal portion of the bottom on each side of the keel. The horizontal region of the bottom is called flat of keel, or flat of bottom. While any section of the ship can have deadrise, tabulated deadrise is normally taken at the midships section.

Knuckle An abrupt change in the direction of plating or other structure.

Chine The line or knuckle formed by the intersection of two relatively flat hull surfaces, continuous over a significant length of the hull. In hard chines, the intersection forms a sharp angle; in soft chines, the connection is rounded.

Bilge radius The outline of the midships section of very full ships is very nearly a rectangle with its lower corners rounded. The lower corners are called the bilges and the shape is often circular. The radius of the circular arc is called the bilge radius or turn of the bilge. The turn of the bilge may be described as hard or easy depending on the radius of curvature. If the shape of the bilge follows some curve other than a circle, the radius of curvature of the bilge will increase as it approaches the straight plating of the side and bottom. Small, high-speed or planing hulls often do not have a rounded bilge. In these craft, the side and bottom are joined in a chine.

Tumblehome The inward fall of side plating from the vertical as it extends upward towards the deck edge. Tumblehome is measured horizontally from the molded breadth line at the deck edge. Tumblehome was a usual feature in sailing ships and many ships built before 1940. Because it is more expensive to construct a hull with tumblehome, this feature is not usually incorporated in modern merchant ship design, unless required by operating conditions or service (tugs and icebreaking vessels, for example). Destroyers and other high-speed combatants are often built with some tumblehome in their mid and after sections to save topside weight.

Flare The outward curvature of the hull surface above the waterline, i.e., the opposite of tumblehome. Flared sections cause a commensurately larger increase in local buoyancy than unflared sections when immersed. Flaring bows are often fitted to help keep the forward decks dry and to prevent "nose-diving" in head seas.

Camber The convex upwards curve of a deck. Also called round up, round down, or round of beam. In section, the camber shape may be parabolic or consist of several straight line segments. Camber is usually given as the height of the deck on the centerline amidships above a horizontal line connecting port and starboard deck edges. Standard camber is about one-fiftieth of the beam. Camber diminishes towards the ends of the ship as the beam decreases. The principal use of camber is to ensure good drainage in calm seas or in port, although camber does slightly increase righting arms at large angles of inclination (after the deck edge is immersed). Not all ships have cambered decks; ships with cambered weather decks and flat internal decks are not uncommon.

Sheer The rise of a deck above the horizontal measured as the height of the deck above a line parallel to the baseline tangent to the deck at its lowest point. In older ships, the deck side line often followed a parabolic profile and sheer was given as its value at the forward and after perpendiculars. Standard sheer was given by: where sheer is measured in inches and L is the length between perpendiculars in feet. Actual sheer often varied considerably from
sheer forward = 0.2L + 20
sheer aft = 0.1L + 10
these standard values; the deck side profile was not always parabolic, the lowest point of the upper deck was usually at about 0.6L, and the values of sheer forward and aft were varied to suit the particular design. Many modern ships are built without sheer; in some, the decks are flat for some distance fore and aft of midships and then rise in a straight line towards the ends. Sheer increases the height of the weather decks above water, particularly at the bow, and helps keep the vessel from shipping water as she moves through rough seas as well as improving sea keeping by adding bouyancy Ford and Aft.

Rake A departure from the vertical or horizontal of any conspicuous line in profile, defined by a rake angle or by the distance between the profile line and a reference line at a convenient point. Rake of stem, for example, can be expressed as the angle between the stem bar and a vertical line for ships with straight stems. For curved stems, a number of ordinates measured from the forward perpendicular are required to define the stem shape. Ships designed so that the keel is not parallel to the baseline and DWL when floating at their designed drafts are said to have raked keels, or to have drag by the keel.

Cut-up When a keel departs from a straight line at a sharp bend, or knuckle, the sloping portion is called a cut-up. This is seen on some high speed craft and on Ice breakers allowing them to ride up on to the ice

Deadwood Portions of the immersed hull with significant longitudinal and vertical dimensions, but without appreciable transverse dimensions. Deadwood is included in a hull design principally to increase lateral resistance or enhance directional stability without significantly increasing drag when moving ahead. Sailing craft require deadwood to be able to work to windward efficiently.
Skegs or fins are fitted on barges to give directional stability. Deadwood aft is detrimental to speed and quick maneuverability and is minimized by use of cut-up sterns and by arched keels or sluice keels (with athwartships apertures) in tugs and workboats.

Appendages Portions of the vessel that extend beyond the main hull outline or molded surface. Positive appendages, such as rudders, shafts, bosses, bilge keels, sonar domes, etc., increase the underwater volume, while negative appendages, such as bow thruster tunnels and other recesses, decrease the underwater volume. Shell plating, lying outside the molded surface, is normally the largest single appendage, and often accounts for one-half to two-thirds of the total appendage volume. Appendages generally account for 0.2 to 2 percent of total immersed hull volume, depending on ship size, service, and configuration.

Hull Surfaces Hull surfaces are either warped, consisting of smoothly faired, complex three-dimensional curves, developed, consisting of portions of cylinders or cones, or flat. Hydroconic hulls are built up of connected flat plates rather than plates rolled to complex curves. Hydroconic construction lowers production costs and may simplify fitting patches to a casualty.
The part of the hull which effects the speed and fuel consumed is the area under the water. Thus Length Overall (L_OA) is not relevant. Instead the length between perpendiculars (L_PP and Length at waterline (L_WL) are used. For L_PP the aftermost perpendicular is usually taken as passing through the rudder stock. An accepted method of calculation is

L_PP = 0.97 x L_WL

The draught is taken as the design draught. This draught depends on the trading of the vessel and may be between the summer loadline draught and ballast draught